Coral Crown — complete SuperCollider settings
Signal flow and implementation #
~soundStage is compiled into the SynthDefs. Re-evaluate the complete block after changing it; source and effects are then replaced together. The fixed output multiplier ~soundOutputScale is 0.8468908 and applies after the whole chain at every stage. It is separate from any final gain step.
EnvGen supplies the explicit linear or exponential contours. Exponential floors stay positive. Closing the gate begins each release; a separate silent lifetime envelope frees the note after the longest source release. Shared effects continue independently.
BPF and BRF use bandwidth divided by center frequency as reciprocal Q. The narrow noise resonances, where present, use SuperCollider normalization and need their own instrument gain.
LeakDC uses coefficient 0.995. It replaces the longer-window Csound DC blocker, with a different low-frequency response and latency.
LocalIn/LocalOut carry all feedback paths in a single multichannel loop. Recirculation adds one server processing block to each delay; changing block size therefore changes short comb/flanger tuning. DelayC uses seconds, converted from the millisecond tap values in the design.
Saw and Pulse use SuperCollider oscillator implementations and startup phases; they replace the source engines and do not scan proprietary wavetables.
~pgTriangle builds an odd-partial sine sum through harmonic 31. It replaces the source triangle oscillator; components at or above 22 kHz are muted.
Synthesis and effect controls #
Stage 1 — Build the detuned source and amplitude contour #
Select ~soundStage = 1 and evaluate the full script at the end of this guide. Wait for the instrument-ready message before playing. The triangle source is an explicit odd-harmonic sine sum through partial 31, with components at or above 22 kHz muted.
Set ~soundStage = 1 in the full script. Use 3 band-limited saw voices at -9 dB each, spread by 6 cents between adjacent voices. Reverse the stereo weights across the channels. The amplitude opens in 0.0044 seconds, decays over 0.582 seconds to 0.630957, and releases over 0.186 seconds. Basic Shapes is represented by this explicit waveform; Shimmer, where present, becomes slow independent pitch drift rather than the original unison engine.
| SuperCollider control | Value |
|---|---|
| Sources | 3 × saw, -9 dB |
| Adjacent pitch spacing | 6 cents |
| Amp A/D/S/R | 0.0044 s / 0.582 s / 0.630957 / 0.186 s |
| Instrument gain | -6 dB |
| Velocity multiplier | 0.4 + 0.6 × velocity |
Stage 2 — Blend the second source and animate the filters #
Set ~soundStage = 2 in the full script. Add a triangle layer at -13 dB, 0 semitones and 5 cents. Add the quieter octave-down sine sub. The notch center starts from 772 Hz and moves by -0.8 octaves under the second envelope. A positive depth opens the spectral ceiling; a negative depth moves the notch downward. The serial second filter keeps the specified high or low edge under control. Exact wavetable morphing, Warp/Fold and free-running source modulation are not implemented; the code below defines the chosen static spectra and note-local drift.
| SuperCollider control | Value |
|---|---|
| Secondary layer | triangle, -13 dB; 0 st; 5 cents |
| Filter 1 | Notch, 772 Hz base, -0.8 octave depth |
| Filter contour | 0.02 / 1.1 / 0.2 / 0.3 |
| Filter 2 | Lowpass at 6.80 kHz |
| Pulse width | Not used |
Stage 3 — Round the signal with saturation #
Set ~soundStage = 3 in the full script. Use +2.4 dB drive with 70% shaped signal and -3 dB output trim. The smooth curve is tanh(input × 3 × drive.dbamp) / 3; the other portion stays clean. Louder peaks enter its curved region more strongly, adding harmonics and rounding the envelope. This interprets the source saturation curve rather than implementing its proprietary transfer function.
| SuperCollider control | Value |
|---|---|
| Drive / output | 2.4 / -3 dB |
| Shaped mix | 70% |
| Input DC removal | LeakDC, coefficient 0.995 |
Stage 4 — Add filtered stereo echoes #
Set ~soundStage = 4 in the full script. Use 267 ms left and 267 ms right, 24% feedback and 18% wet. Inject the centered input on the left and cross-feed the filtered echoes so later repeats alternate sides. Filter each echo around 1800 Hz, with a 3.5-octave interval between highpass and lowpass cutoffs. Feedback values are updated once per server processing block, adding that small delay to the recirculating path. Held notes leave older colors behind the current tone.
| SuperCollider control | Value |
|---|---|
| Times | 267 / 267 ms |
| Feedback / wet | 24% / 18% |
| Routing | Crossed, left input |
| Filter center / width | 1800 Hz / 3.5 octaves |
| Time LFO | 0 Hz, ±0% |
Stage 5 — Set the final width and gain #
Set ~soundStage = 5 in the full script. Use 5.27 dB gain after the effects. Scale the side signal by 1, preserving the center. Apply LeakDC DC removal with coefficient 0.995. The fixed ~soundOutputScale gain follows the complete effect chain at every stage. The effects Synth reads the stereo bus after the note group, and continues through note releases.
| SuperCollider control | Value |
|---|---|
| Final gain | 5.27 dB |
| Width | 1 × side |
| Bass side cutoff | Off |
| DC removal | LeakDC, coefficient 0.995 |
Connected instrument #
The full SuperCollider script contains the complete voice, shared effects, bus ordering and note helper. No external sample or third-party unit is required.