Step 01 / 5
Build the airy Swarm Triangle swell #
Choose Swarm Triangle for engine A. Motion at 28 makes the triangle cluster noticeably more animated, while Spacing at 24 separates its internal voices without using stacked-voice mode. The 650 ms attack creates a soft entrance; the 3.20-second decay settles toward a -4 dB sustain level, and the 1.90-second release lets the tone fade naturally. Keep the filter bypassed in this stage so the oscillator’s motion is exposed before the brighter boundary is added.
Use Meld with the complete starting settings. Set the source and amplitude controls below; sections marked Off stay bypassed at this stage.
Signal flow: Meld → Delay → Reverb → Utility. Begin with the instrument, then add each effect in its numbered step.
| Control | Value |
|---|---|
| A On | On |
| A Osc Type | Swarm Triangle (♭♯) |
| A Osc Motion | 28.0 |
| A Osc Spacing | 24.0 |
| A Volume | -10 dB |
| A Amp Attack | 650 ms |
| A Amp Decay | 3.20 s |
| A Amp Sustain | -4.0 dB |
| A Amp Release | 1.90 s |
| Drive | 5.0 % |
| Volume | -8.0 dB |
| Scale Aware | Off |
| B On | Off |
| A Filter On | Off |
| Voice Spread | 0 % |
Voicing and modulation #
Set these voice and controller assignments for both engines. Unlisted modulation cells remain at zero. Spread moves each engine’s detuning and pan in opposite directions. The engine oscillator macros provide additional internal motion.
| Control | Value |
|---|---|
| Voicing | Poly |
| Poly voices | 8 |
| Stacked voices | Off |
| Spread → A Detune | 50 |
| Pitch Bend → A Pitch Mod | 7 st |
| Note Pitch Bend → A Pitch Mod | 48 st |
| Spread → A Pan | 50 |
| Velocity → A Volume | 50 |
| Spread → B Detune | -50 |
| Pitch Bend → B Pitch Mod | 7 st |
| Note Pitch Bend → B Pitch Mod | 48 st |
| Spread → B Pan | -50 |
| Velocity → B Volume | 50 |
Use the voicing and modulation settings for the oscillator choices, voice mode and modulation routes.

Sound after step 1 — WebM/Opus
Next: Add the slower octave bloom and stereo spread →Step 02 / 5
Add the slower octave bloom and stereo spread #
Enable engine B as a quiet Basic Shapes voice one octave above engine A. Its 1.10-second attack trails the main swell, while its -22 dB level and four-second decay create a light upper bloom rather than a separate melody voice. Turn on engine A’s SVF 12 dB filter at 2.60 kHz: this is brighter than Cinder Orbit’s related topology and preserves more of the Swarm Triangle’s airy motion.
Set Voice Spread to 25%. The routing table sends A and B toward opposite detune and pan directions, widening the pad without stacked voices. Bass Mono later keeps frequencies below 160 Hz centered.
Keep the first stage’s source and amplitude settings while making these changes. The complete instrument settings show the resulting tone before effects.
| Control | Value |
|---|---|
| A Filter Type | SVF 12dB |
| A Filter Freq | 2.60 kHz |
| A Filter Q | 12.0 |
| B On | On |
| B Osc Type | Basic Shapes |
| B Osc Shape | 0.0 |
| B Osc Tone | 0.0 |
| B Octave | 1 oct |
| B Volume | -22 dB |
| B Filter Freq | 3.60 kHz |
| B Amp Attack | 1.10 s |
| B Amp Decay | 4.00 s |
| B Amp Sustain | -6.0 dB |
| B Amp Release | 2.20 s |
| Voice Spread | 25 % |
| A Filter On | On |

Sound after step 2 — WebM/Opus
Next: Add wandering beacon-like echoes →Step 03 / 5
Add wandering beacon-like echoes #
Set the left and right delays to unequal 340 ms and 470 ms times with Ping Pong on. The offset repeats answer from different positions, reinforcing the distant beacon-like character. Filter them around 1.70 kHz, then use the 0.18 Hz LFO at 2% delay modulation and 4% filter modulation so the echoes wander slowly without overtaking the direct pad.
| Control | Value |
|---|---|
| L Sync | Off |
| R Sync | Off |
| Link | Off |
| L Time | 340 ms |
| R Time | 470 ms |
| Ping Pong | On |
| Feedback | 30 % |
| Dry/Wet | 22 % |
| Filter Freq | 1.70 kHz |
| Filter Width | 3.00 |
| LFO Freq | 0.18 Hz |
| LFO > Delay | 2.0 % |
| LFO > Filter | 4.0 % |
| Freeze | Off |
Place Delay after Meld. The complete settings include its remaining controls.

Sound after step 3 — WebM/Opus
Next: Add a soft distant room →Step 04 / 5
Add a soft distant room #
Use a 3.30-second decay and 90 room size at 20% Dry/Wet. The 30 ms predelay preserves the initial swell before the room appears, while high-frequency damping above 3.20 kHz softens the tail without removing the brighter Meld body.
| Control | Value |
|---|---|
| Predelay | 30.0 ms |
| In Lo Cut On | Off |
| In Hi Cut On | Off |
| Diff. Hi Freq | 3.20 kHz |
| HiShelf Gain | 0.60 |
| Density | High |
| Freeze On | Off |
| Decay Time | 3.30 s |
| Room Size | 90.00 |
| Dry/Wet | 20 % |
Place Reverb after Delay. The complete settings include its remaining controls.

Sound after step 4 — WebM/Opus
Next: Focus the low end and set the final level →Step 05 / 5
Focus the low end and set the final level #
Turn Bass Mono on at 160 Hz to anchor the lowest frequencies beneath the spread engines and moving echoes. Keep full-band width at 100% and DC Filter on. Set Utility’s Gain knob to the Output value in the table; it establishes the final level without changing the airy oscillator and filter balance.
| Control | Value |
|---|---|
| Output | 16.5 dB |
| DC Filter | On |
| Bass Mono | On |
| Bass Freq | 160 Hz |
Place Utility after Reverb. The complete settings include its remaining controls.

Sound after step 5 — WebM/Opus
Audio & settings ↓