playgrid.ccRead tutorial

Quartz Ripple — complete Csound settings

Note and effect connections

Instrument 1 uses p3 for held seconds, p4 for MIDI pitch and p5 for velocity from 0 to 1. Its left and right outputs accumulate on shared buses. Instrument 90 processes the buses once per control block, clears the inputs and keeps effect memories active through the tails. Envelopes with release segments extend the note automatically. The score is an audible pitch-and-touch example; the synthesis controls are independent of its particular notes.

Csound interpretation

These are explicit Csound models, not identical implementations of the Ableton devices. Wavetable positions, proprietary oscillator engines, physical-model macros, filter circuits, envelope slopes and effect algorithms can differ. Modulation depths are specified in octaves, cents or milliseconds rather than treated as universally interchangeable matrix values. Controller inputs such as pitch bend, modulation wheel, pressure and per-note expression are not mapped. Independent score notes do not implement Live's monophonic note-priority or legato system. Any pitch memory or drift included in this instrument is described in its steps.

Signal path and controls

Stage 1 — Build the drifting triangle cluster

Use five triangle voices spread across ±12 cents, with independent sine drift of ±1.2 cents. Their different phases and slow rates make the held spectrum beat. Use engine gain −10 dB, amplitude attack 1.03 s, decay 3.2 s to −4 dB and release 1.73 s. A −8 dB instrument gain and 50% velocity response follow mild smooth drive. Spacing and motion are explicit Csound choices for the source macros.

Csound control Value
Triangle offsets −12, −6, 0, +6, +12 cents
Drift ±1.2 cents; 0.12 + abs(offset) × 0.005 Hz
A contour 1.03 / 3.2 / −4 dB / 1.73 s
Engine / instrument gain −10 / −8 dB

Stage 2 — Add the slower octave and stereo filtering

Enable the octave-up sine at −22 dB and +3.125 cents. Give it an independent 1.10 s attack, 4 s decay to −6 dB and 2.20 s release. Filter the triangle channels at 1720 Hz with Q 1.2; reverse the voice weights across the channels, bias A slightly left and B right. The octave enters later than the main cluster and can remain after its release. This interprets Basic Shapes and SVF rather than scanning the original engines.

Csound control Value
A lowpass 1720 Hz, Q 1.2
B pitch / level 2 × note frequency, +3.125 cents / −22 dB
B contour 1.10 / 4.00 / −6 dB / 2.20 s
Stereo voice weights 0.8/0.7/0.5/0.3/0.2, reversed right; sum / 2.5

Stage 3 — Add filtered stereo echoes

Use 340 ms left and 470 ms right, 30% feedback and 22% wet. Inject the centered input on the left and cross-feed the filtered echoes so later repeats alternate sides. Filter each echo around 1700 Hz, with a 3-octave interval between highpass and lowpass cutoffs. A shared 0.18 Hz sine moves times by ±2% and the filter center by ±0.04 octaves. Feedback values are updated once per 16-sample block, adding that small delay to the recirculating path. Held notes leave older colors behind the current tone.

Csound control Value
Times 340 / 470 ms
Feedback / wet 30% / 22%
Routing Crossed, left input
Filter center / width 1700 Hz / 3 octaves
Time LFO 0.18 Hz, ±2%

Stage 4 — Surround the tone with a damped room

Feed the preceding signal through 30 ms predelay into reverbsc, with feedback 0.8119, 3200 Hz damping and 20% wet mix. Predelay leaves the initial articulation in front; feedback prolongs the tail, while damping darkens repeated circulation. The source room decay setting is 3.36 seconds, but Csound feedback is not a decay-time control: this is an interpretation of that space, with different diffusion and modulation.

Csound control Value
Source decay target 3.36 s (not a measured Csound decay)
Predelay / feedback 30 ms / 0.8119
Damping / wet 3200 Hz / 20%
Room side multiplier 1
Room input cuts Off

Stage 5 — Set the final width and gain

Use 6.24 dB gain after the effects. Scale the side signal by 1, preserving the center. Highpass only the side at 160 Hz to focus the lowest frequencies. Apply order-2048 DC removal, using a longer window to limit low-note loss. The fixed output-scale control at the end of instrument 90 remains a separate Csound gain setting. Clear the shared note buses only after processing them; effect memories continue carrying their own tails.

Csound control Value
Final gain 6.24 dB
Width 1 × side
Bass side cutoff 160 Hz
DC removal Order 2048

Output and signal rates

The script uses 48000 Hz, 16-sample control blocks and stereo output. The fixed output-scale control is 1.200192 and follows the whole chain at every stage, separate from any final gain step. DC-removal blocks, where enabled, use order 2048 to limit low-note attenuation; they add processing delay.

Build guide and full script · Starting settings