Slow Harmonic Pad — complete SuperCollider settings
Signal flow and implementation #
~soundStage is compiled into the SynthDefs. Re-evaluate the complete block after changing it; source and effects are then replaced together. The fixed output multiplier ~soundOutputScale is 1.133972 and applies after the whole chain at every stage. It is separate from any final gain step.
EnvGen supplies the explicit linear or exponential contours. Exponential floors stay positive. Closing the gate begins each release; a separate silent lifetime envelope frees the note after the longest source release. Shared effects continue independently.
LocalIn/LocalOut carry all feedback paths in a single multichannel loop. Recirculation adds one server processing block to each delay; changing block size therefore changes short comb/flanger tuning. DelayC uses seconds, converted from the millisecond tap values in the design.
~pgWave uses the explicitly specified unnormalized harmonic coefficients. Each component is muted at or above 22 kHz rather than folded back into the spectrum.
Synthesis and effect controls #
Stage 1 — Draw the high ringing center #
Select ~soundStage = 1 and evaluate the full script at the end of this guide. Wait for the instrument-ready message before playing.
Set ~soundStage = 1 in the full script. Use the three-partial A table at ratio 9 and global transposition −14 semitones. Its partials have levels 0, −2.3 and −10.5 dB. A opens over 2.057 seconds and releases over 4.3 seconds. The high ratio supplies the ringing center; table amplitudes remain unnormalized.
| SuperCollider control | Value |
|---|---|
| A partials | 1: 0 dB; 2: −2.3 dB; 3: −10.5 dB |
| A ratio / transpose | 9 / −14 st |
| A envelope | 2.057 s attack; full sustain; 4.3 s release |
| Instrument | −33 dB |
Stage 2 — Fill in the lower harmonic spectra #
Set ~soundStage = 2 in the full script. Add the documented B and C spectra through partial 38, with different attacks and a B frequency ratio of 1.003. Add D with its quiet low odd harmonics. The exact partial coefficients are written in the full script. Their different onset and release times make the texture change as it grows and fades; B fine tuning is an explicit ratio interpretation.
| SuperCollider control | Value |
|---|---|
| B | −1.9 dB; 2.294 s attack; 3.7 s release; ratio 1.003 |
| C | −9.1 dB; 2.8 s attack; 4.1 s release; ratio 1 |
| D | −6 dB; 2.38 s attack; 4 s release; ratio 1 |
| Tables | Unnormalized sine sums; unlisted partials zero |
Stage 3 — Add moving stereo chorus #
Set ~soundStage = 3 in the full script. Also apply source amplitude movement 0.82 + 0.18 × sine(0.35 Hz). The explicit 0.35 Hz rate interprets the source displayed LFO rate 35. Move two delay taps around 7 ms by ±3.4 ms at 0.9 Hz, with opposite phases and 100% wet mix. The wet inputs remain full-band. Scale side information by 1.3; tap feedback is -0.02. These explicit tap depths interpret the source Amount and ensemble movement rather than copy the internal algorithm. Sustained notes reveal slow pitch interference.
| SuperCollider control | Value |
|---|---|
| Tap center / excursion | 7 / ±3.4 ms |
| Rate / wet | 0.9 Hz / 100% |
| Wet highpass | Off |
| Width / feedback | 1.3 / -0.02 |
| Warmth shaping | 0% smooth-drive interpretation |
| Source amplitude LFO | 0.35 Hz; multiplier 0.82 + 0.18 × sine |
Connected instrument #
The full SuperCollider script contains the complete voice, shared effects, bus ordering and note helper. No external sample or third-party unit is required.