Sorrel Signal — Wavetable starting settings
Use these settings for the first synthesis stage. Step 2 enables the additional sources or shaping sections and gives their final values.
Wavetable #
| Control | Value |
|---|---|
| Device On | On |
| Osc 1 On | On |
| Osc 1 Transp | 0 st |
| Osc 1 Detune | 0 ct |
| Osc 1 Pos | 66 % |
| Osc 1 Effect 1 | 0.0 % |
| Osc 1 Effect 2 | 0.0 % |
| Osc 1 Pan | C |
| Osc 1 Gain | -9.0 dB |
| Osc 2 On | Off |
| Osc 2 Transp | 0 st |
| Osc 2 Detune | 5 ct |
| Osc 2 Pos | 46 % |
| Osc 2 Effect 1 | 0.0 % |
| Osc 2 Effect 2 | 0.0 % |
| Osc 2 Pan | C |
| Osc 2 Gain | -13 dB |
| Sub On | Off |
| Sub Tone | 0.0 % |
| Sub Gain | -18 dB |
| Sub Transpose | -1 |
| Flt 1 On | Off |
| Flt 1 Type | Notch |
| Flt 1 LP/HP | Clean |
| Flt 1 BP/NO/MO | Clean |
| Flt 1 Slope | 12 |
| Flt 1 Freq | 787 Hz |
| Flt 1 Res | 22 % |
| Flt 1 Drive | 0.00 dB |
| Flt 1 Morph | 0 lp/bp |
| Flt 2 On | Off |
| Flt 2 Type | Lowpass |
| Flt 2 LP/HP | Clean |
| Flt 2 BP/NO/MO | Clean |
| Flt 2 Slope | 12 |
| Flt 2 Freq | 6.80 kHz |
| Flt 2 Res | 5.0 % |
| Flt 2 Drive | 0.00 dB |
| Flt 2 Morph | 0 lp/bp |
| Amp Attack | 13.7 ms |
| Amp Decay | 1.79 s |
| Amp Release | 470 ms |
| Amp A Slope | 0.0 % |
| Amp D Slope | 50 % |
| Amp R Slope | 50 % |
| Amp Sustain | -4.0 dB |
| Amp Loop Mode | None |
| Env 2 Attack | 20.0 ms |
| Env 2 Decay | 1.10 s |
| Env 2 Release | 300 ms |
| Env 2 A Slope | 0.0 % |
| Env 2 D Slope | 50 % |
| Env 2 R Slope | 50 % |
| Env 2 Initial | 0.0 % |
| Env 2 Peak | 100 % |
| Env 2 Sustain | 20 % |
| Env 2 Final | 0.0 % |
| Env 2 Loop Mode | None |
| Env 3 Attack | 1.00 ms |
| Env 3 Decay | 600 ms |
| Env 3 Release | 600 ms |
| Env 3 A Slope | 0.0 % |
| Env 3 D Slope | 50 % |
| Env 3 R Slope | 50 % |
| Env 3 Initial | 0.0 % |
| Env 3 Peak | 100 % |
| Env 3 Sustain | 50 % |
| Env 3 Final | 0.0 % |
| Env 3 Loop Mode | None |
| LFO 1 Retrigger | On |
| LFO 1 Shape | Sine |
| LFO 1 Amount | 100 % |
| LFO 1 Shaping | 0.0 % |
| LFO 1 Phase Offset | 0.0° |
| LFO 1 Sync | Free |
| LFO 1 Rate | 1.00 Hz |
| LFO 1 S. Rate | 1/8 |
| LFO 1 Attack Time | 0.00 ms |
| LFO 2 Retrigger | On |
| LFO 2 Shape | Sine |
| LFO 2 Amount | 100 % |
| LFO 2 Shaping | 0.0 % |
| LFO 2 Phase Offset | 0.0° |
| LFO 2 Sync | Free |
| LFO 2 Rate | 1.00 Hz |
| LFO 2 S. Rate | 1/8 |
| LFO 2 Attack Time | 0.00 ms |
| Time | 0.0 % |
| Global Mod Amount | 100 % |
| Unison Amount | 10 % |
| Transpose | 0 st |
| Glide | 40.0 ms |
| Volume | -6.0 dB |
Voicing and modulation #
Choose the waveform and voicing controls below. In the Matrix and MIDI tabs, set the listed routes; leave unlisted routes at zero. The modulation amounts are the values shown in the matrix. Poly voices apply in Poly mode.
| Control | Value |
|---|---|
| Oscillator 1 category | Basics |
| Oscillator 1 wavetable | Basic Shapes |
| Oscillator 1 effect mode | None |
| Oscillator 2 category | Basics |
| Oscillator 2 wavetable | Basic Shapes |
| Oscillator 2 effect mode | None |
| Voicing | Mono |
| Poly voices | 8 |
| Unison mode | Classic |
| Unison voices | 3 |
| Filter routing | Serial |
| Velocity → Volume | 60 |
| Pitch Bend → Transpose | 2 st |
| Env 2 → Flt 1 Freq | -16 |
| Velocity → Flt 2 Freq | 7 |
| Mod Wheel → Flt 2 Freq | 15 |