Submerged Pulse Horn — complete SuperCollider settings
Signal flow and implementation #
~soundStage is compiled into the SynthDefs. Re-evaluate the complete block after changing it; source and effects are then replaced together. The fixed output multiplier ~soundOutputScale is 0.4362782 and applies after the whole chain at every stage. It is separate from any final gain step.
EnvGen supplies the explicit linear or exponential contours. Exponential floors stay positive. Closing the gate begins each release; a separate silent lifetime envelope frees the note after the longest source release. Shared effects continue independently.
BPF and BRF use bandwidth divided by center frequency as reciprocal Q. The narrow noise resonances, where present, use SuperCollider normalization and need their own instrument gain.
FreeVerb2 replaces the diffuse room with its own room and damping controls, both dimensionless. The per-stage values below are specific to this algorithm and do not specify a measured decay time or damping frequency.
Saw and Pulse use SuperCollider oscillator implementations and startup phases; they replace the source engines and do not scan proprietary wavetables.
Synthesis and effect controls #
Stage 1 — Build the low body and reedy upper edge #
Select ~soundStage = 1 and evaluate the full script at the end of this guide. Wait for the instrument-ready message before playing.
Set ~soundStage = 1 in the full script. Use a 10% pulse at −8 dB and a quiet upper sine at +16 st/−14 cents, −21 dB. A mild tanh shape interprets the upper source warp. Bandpass the main pair at 400 Hz and notch near 805 Hz, while allowing the octave-down sine to bypass those filters and preserve the low anchor. That explicit sub bypass is a SuperCollider interpretation of the source balance. Use a 24 ms opening, full sustain and 3.3 s release.
| SuperCollider control | Value |
|---|---|
| Main / upper | Pulse width 0.10 at −8 dB; sine +16 st/−14 cents at −21 dB |
| Sub | Octave-down sine, 0 dB, bypasses main filters |
| Filters | 400 Hz bandpass, bandwidth = center; 805 Hz notch, bandwidth = 15% center |
| Tracking | Bandpass 70%; notch 100% |
| Amplitude | 24 ms / 1.28 s / full / 3.3 s |
| Touch | 0.2 + 0.8 × velocity |
Stage 2 — Let the bandpass rise after the attack #
Set ~soundStage = 2 in the full script. Open the bandpass by 0.4 octaves under a 510 ms / 1.81 s / zero / 1.35 s contour. The amplitude arrives much earlier than the filter peak, making the color swell over the established low body. The modulation depth and bandwidth interpret the source matrix and resonance values rather than copy its circuits.
| SuperCollider control | Value |
|---|---|
| Filter contour | 510 ms / 1.81 s / zero / 1.35 s |
| Filter motion | +0.4 octaves |
Stage 3 — Round the signal with saturation #
Set ~soundStage = 3 in the full script. Use +3 dB drive with 100% shaped signal and -3 dB output trim. The smooth curve is tanh(input × 3 × drive.dbamp) / 3; the other portion stays clean. Louder peaks enter its curved region more strongly, adding harmonics and rounding the envelope. This interprets the source saturation curve rather than implementing its proprietary transfer function.
| SuperCollider control | Value |
|---|---|
| Drive / output | 3 / -3 dB |
| Shaped mix | 100% |
| Input DC removal | Off |
Stage 4 — Widen a dark room around the horn #
Set ~soundStage = 4 and evaluate the full block. Feed the preceding signal into FreeVerb2, using its fully wet output and the dry/wet routing shown in the script. The room continues after individual note envelopes release. Predelay separates the initial articulation from the diffuse tail; the external wet mix controls how far that tail moves forward.
The SuperCollider room value is 0.942951 and damping is 0.84375. These dimensionless settings are choices for this algorithm, rather than equivalent values for Ableton decay or Csound feedback and damping. More damping darkens the circulating highs. Any input filters and mid/side width changes in this stage retain their own explicit settings in the full script.
| SuperCollider room control | Value |
|---|---|
| FreeVerb2 internal mix | 1, wet output only |
| Room | 0.942951 |
| Damping | 0.84375 |
| Predelay | 10 ms |
| External room wet | 40% |
| SuperCollider control | Value |
|---|---|
| Room side multiplier | 1 |
| Room input cuts | 275 / 4400 Hz |
| Final gain | 1.5 dB |
| Width | 3 × side |
| Bass side cutoff | Off |
| DC removal | Off |
The same stage also applies the output gain and side-width controls shown in the full script; low-cut and high-cut processing affect the room input rather than the direct tone.
Connected instrument #
The full SuperCollider script contains the complete voice, shared effects, bus ordering and note helper. No external sample or third-party unit is required.