Step 01 / 5
Choose the first wavetable and amplitude contour #
Choose oscillator 1’s wavetable, position and tuning. Set the amplifier envelope and voicing from the starting settings. Wavetable position chooses the harmonic shape; the amplitude envelope controls how the sound arrives and fades.
Use Wavetable with the complete starting settings. Set the source and amplitude controls below; sections marked Off stay bypassed at this stage.
Signal flow: Wavetable → Saturator → Delay → Utility. Begin with the instrument, then add each effect in its numbered step.
| Control | Value |
|---|---|
| Osc 1 On | On |
| Osc 1 Pos | 66 % |
| Osc 1 Gain | -9.0 dB |
| Amp Attack | 4.40 ms |
| Amp Decay | 640 ms |
| Amp Sustain | -4.0 dB |
| Amp Release | 380 ms |
| Unison Amount | 10 % |
| Glide | 40.0 ms |
| Volume | -6.0 dB |
| Osc 2 On | Off |
| Sub On | Off |
| Flt 1 On | Off |
| Flt 2 On | Off |
Voicing and modulation #
Choose the waveform and voicing controls below. In the Matrix and MIDI tabs, set the listed routes; leave unlisted routes at zero. The modulation amounts are the values shown in the matrix. Poly voices apply in Poly mode.
| Control | Value |
|---|---|
| Oscillator 1 category | Basics |
| Oscillator 1 wavetable | Basic Shapes |
| Oscillator 1 effect mode | None |
| Oscillator 2 category | Basics |
| Oscillator 2 wavetable | Basic Shapes |
| Oscillator 2 effect mode | None |
| Voicing | Mono |
| Poly voices | 8 |
| Unison mode | Classic |
| Unison voices | 3 |
| Filter routing | Serial |
| Velocity → Volume | 60 |
| Pitch Bend → Transpose | 2 st |
| Env 2 → Flt 1 Freq | -16 |
| Velocity → Flt 2 Freq | 7 |
| Mod Wheel → Flt 2 Freq | 15 |
Use the voicing and modulation settings for the oscillator choices, voice mode and modulation routes.
Sound after step 1 — WebM/Opus
Next: Layer the oscillators and animate the filters →Step 02 / 5
Layer the oscillators and animate the filters #
Enable the additional sources and filters using the states below. Balance oscillator 2 against oscillator 1, then set the filter types, cutoff and resonance. Apply the listed envelope and LFO routes in the instrument’s Matrix and MIDI tabs; unlisted routes stay at zero.
Keep the first stage’s source and amplitude settings while making these changes. The complete instrument settings show the resulting tone before effects.
| Control | Value |
|---|---|
| Osc 2 On | On |
| Osc 2 Pos | 65 % |
| Osc 2 Gain | -13 dB |
| Osc 2 Detune | 5 ct |
| Sub On | On |
| Sub Gain | -18 dB |
| Sub Tone | 0.0 % |
| Flt 1 Type | Notch |
| Flt 1 BP/NO/MO | Clean |
| Flt 1 Freq | 913 Hz |
| Flt 1 Res | 22 % |
| Flt 2 On | On |
| Flt 2 Type | Lowpass |
| Flt 2 Freq | 6.80 kHz |
| Flt 2 Res | 5.0 % |
| Env 2 Attack | 20.0 ms |
| Env 2 Decay | 1.10 s |
| Env 2 Sustain | 20 % |
| Env 2 Release | 300 ms |
| Flt 1 On | On |
Sound after step 2 — WebM/Opus
Next: Apply Saturator →Step 03 / 5
Apply Saturator #
Select the curve before setting Drive. Drive changes the waveform’s harmonic content; Output balances the level after that change. Dry/Wet blends the processed and direct tone. Keep Color and clipping controls as listed because they alter the distortion character.
| Control | Value |
|---|---|
| Type | Analog Clip |
| Drive | 2.9 dB |
| Output | -3.0 dB |
| Color On | Off |
| Pre Dc Filter | On |
| Dry/Wet | 70 % |
Place Saturator after Wavetable. The complete settings include its remaining controls.
Sound after step 3 — WebM/Opus
Next: Apply Delay →Step 04 / 5
Apply Delay #
Set the left and right delay modes and times, then set Feedback and Dry/Wet. Unequal times create a stereo echo pattern. Feedback changes how long repeats persist; filtering changes their tone. The modulation controls move the delay’s timing or filter when their amounts are above zero.
| Control | Value |
|---|---|
| L Sync | Off |
| R Sync | Off |
| Link | On |
| L Time | 267 ms |
| R Time | 267 ms |
| Ping Pong | On |
| Feedback | 24 % |
| Dry/Wet | 18 % |
| Filter Freq | 1.80 kHz |
| Filter Width | 3.50 |
| Freeze | Off |
Place Delay after Saturator. The complete settings include its remaining controls.
Sound after step 4 — WebM/Opus
Next: Apply Utility →Step 05 / 5
Apply Utility #
Set gain and width at the end of the chain. Set Utility’s Gain knob to the Output value in the table. Width changes the balance between center and side information; Mono combines the channels. Bass Mono narrows only the low frequencies below its cutoff. Keep DC Filter and phase-inversion switches at the listed values.
| Control | Value |
|---|---|
| Output | 5.72 dB |
| DC Filter | On |
Place Utility after Delay. The complete settings include its remaining controls.
Sound after step 5 — WebM/Opus
Audio & settings ↓