Lo-Fi Bell starting settings
Apply these Wavetable settings for step 1 in Live 12.4 Suite. Enable both main oscillators and Sub. Choose Basics → Basic Shapes, Position 25% and Effect None for both main oscillators. Center both oscillator pans. Leave both filters Off for this step; enable Filter 1 in step 2. Add Reverb in step 3, then Auto Pan-Tremolo and Redux in step 4.
Tune oscillator 1 to +16 st / +30 ct at −21 dB, and oscillator 2 to +18 st / −15 ct at −24 dB. Set Sub Octave −2, Sub Tone 12%, Sub Gain −6.0 dB and global Transpose +12 st.
Use Poly 5, Unison None, Glide 0 ms, Volume −7.0 dB, Time 0% and Global Mod Amount 100%. Set filter routing to Serial.
Set the amplitude envelope to Attack 1.00 ms, Decay 4.30 s, Sustain −38 dB and Release 350 ms. Use Attack Slope 0%, Decay Slope 50%, Release Slope 50% and Loop None.
The only active MIDI modulation connections are Velocity → Amp 50, Pitch Bend → Pitch +2 st and Mod Wheel → Osc 1 Position 15. Set all other matrix connections to zero, including envelope, LFO, note and aftertouch modulation.
Wavetable parameters #
Inactive controls are included for completeness. Filter 1 settings take effect when enabled in step 2; envelope and LFO settings only affect destinations assigned in the matrix.
| Parameter | Displayed value |
|---|---|
| Device On | On |
| Osc 1 On | On |
| Osc 1 Transp | 16 st |
| Osc 1 Detune | 30 ct |
| Osc 1 Pos | 25 % |
| Osc 1 Effect 1 | 0.0 % |
| Osc 1 Effect 2 | 0.0 % |
| Osc 1 Pan | C |
| Osc 1 Gain | -21 dB |
| Osc 2 On | On |
| Osc 2 Transp | 18 st |
| Osc 2 Detune | -15 ct |
| Osc 2 Pos | 25 % |
| Osc 2 Effect 1 | 0.0 % |
| Osc 2 Effect 2 | 0.0 % |
| Osc 2 Pan | C |
| Osc 2 Gain | -24 dB |
| Sub On | On |
| Sub Tone | 12 % |
| Sub Gain | -6.0 dB |
| Sub Transpose | -2 |
| Flt 1 On | Off |
| Flt 1 Type | Lowpass |
| Flt 1 LP/HP | PRD |
| Flt 1 BP/NO/MO | Clean |
| Flt 1 Slope | 24 |
| Flt 1 Freq | 1.65 kHz |
| Flt 1 Res | 34 % |
| Flt 1 Drive | 0.00 dB |
| Flt 1 Morph | 0 lp/bp |
| Flt 2 On | Off |
| Flt 2 Type | Highpass |
| Flt 2 LP/HP | Clean |
| Flt 2 BP/NO/MO | Clean |
| Flt 2 Slope | 12 |
| Flt 2 Freq | 20.0 Hz |
| Flt 2 Res | 0.0 % |
| Flt 2 Drive | 0.00 dB |
| Flt 2 Morph | 0 lp/bp |
| Amp Attack | 1.00 ms |
| Amp Decay | 4.30 s |
| Amp Release | 350 ms |
| Amp A Slope | 0.0 % |
| Amp D Slope | 50 % |
| Amp R Slope | 50 % |
| Amp Sustain | -38 dB |
| Amp Loop Mode | None |
| Env 2 Attack | 1.00 ms |
| Env 2 Decay | 600 ms |
| Env 2 Release | 600 ms |
| Env 2 A Slope | 0.0 % |
| Env 2 D Slope | 50 % |
| Env 2 R Slope | 50 % |
| Env 2 Initial | 0.0 % |
| Env 2 Peak | 100 % |
| Env 2 Sustain | 50 % |
| Env 2 Final | 0.0 % |
| Env 2 Loop Mode | None |
| Env 3 Attack | 1.00 ms |
| Env 3 Decay | 600 ms |
| Env 3 Release | 600 ms |
| Env 3 A Slope | 0.0 % |
| Env 3 D Slope | 50 % |
| Env 3 R Slope | 50 % |
| Env 3 Initial | 0.0 % |
| Env 3 Peak | 100 % |
| Env 3 Sustain | 50 % |
| Env 3 Final | 0.0 % |
| Env 3 Loop Mode | None |
| LFO 1 Retrigger | On |
| LFO 1 Shape | Sine |
| LFO 1 Amount | 100 % |
| LFO 1 Shaping | 0.0 % |
| LFO 1 Phase Offset | 0.0° |
| LFO 1 Sync | Free |
| LFO 1 Rate | 1.00 Hz |
| LFO 1 S. Rate | 1/8 |
| LFO 1 Attack Time | 0.00 ms |
| LFO 2 Retrigger | On |
| LFO 2 Shape | Sine |
| LFO 2 Amount | 100 % |
| LFO 2 Shaping | 0.0 % |
| LFO 2 Phase Offset | 0.0° |
| LFO 2 Sync | Free |
| LFO 2 Rate | 1.00 Hz |
| LFO 2 S. Rate | 1/8 |
| LFO 2 Attack Time | 0.00 ms |
| Time | 0.0 % |
| Global Mod Amount | 100 % |
| Unison Amount | 30 % |
| Transpose | 12 st |
| Glide | 0.00 ms |
| Volume | -7.0 dB |