Step 01 / 5
Strike the tone-bar modes #
Select ~soundStage = 1 and evaluate the full script at the end of this guide. Wait for the instrument-ready message before playing.
Set ~soundStage = 1 in the full script. A hammer pulse rises in 0.3 ms and then falls over 0.0014 seconds. Add 10% contact noise and lowpass the excitation at 5520 Hz, with velocity darkening gentler strikes. Modes at ratios 1 and 2.01 decay over 2.8 and 1.8 seconds. The contact duration and bandwidth give the two electric-key sounds different attacks. These resonances interpret Electric's tone bar and hammer rather than simulate its complete mechanics.
| SuperCollider control | Value |
|---|---|
| Mode ratios / weights | 1 / 2.01; weights 0.75 / 0.18 |
| Modal T60 | 2.8 / 1.8 s |
| Strike bandwidth | 5520 × (0.5 + 0.5 × velocity) Hz |
| Modal scale | 0.02 |
| Instrument / touch | −12 dB / velocity^1.6 |
Sound after step 1 — WebM/Opus
Next: Blend the brighter tine and pickup response →Step 02 / 5
Blend the brighter tine and pickup response #
Set ~soundStage = 2 in the full script. Add modes near ratios 6.98 and 10.03 with 1.36 s and 0.7 s decays. Weight them 0.45 and 0.15, then multiply by the tine blend 0.48. They put a brief bell-like edge above the tone bar. A velocity-dependent tanh curve interprets pickup nonlinearity before the shared effects. Pickup distance, symmetry, damping and release macros are not directly modeled; the script specifies its own contact, resonance and tail behavior.
| SuperCollider control | Value |
|---|---|
| Tine ratios / decays | 6.98 / 10.03; 1.36 / 0.70 s |
| Tine blend | 0.48 |
| Pickup curve | tanh(tone × (1 + 2 × velocity)) / (1 + 2 × velocity) |
| Tail lifetime | 6 s beyond held duration |
Sound after step 2 — WebM/Opus
Next: Round the signal with saturation →Step 03 / 5
Round the signal with saturation #
Set ~soundStage = 3 in the full script. Use +2 dB drive with 45% shaped signal and -2 dB output trim. The smooth curve is tanh(input × 3 × drive.dbamp) / 3; the other portion stays clean. Louder peaks enter its curved region more strongly, adding harmonics and rounding the envelope. This interprets the source saturation curve rather than implementing its proprietary transfer function.
| SuperCollider control | Value |
|---|---|
| Drive / output | 2 / -2 dB |
| Shaped mix | 45% |
| Input DC removal | LeakDC, coefficient 0.995 |
Sound after step 3 — WebM/Opus
Next: Surround the tone with a damped room →Step 04 / 5
Surround the tone with a damped room #
Set ~soundStage = 4 and evaluate the full block. Feed the preceding signal into FreeVerb2, using its fully wet output and the dry/wet routing shown in the script. The room continues after individual note envelopes release. Predelay separates the initial articulation from the diffuse tail; the external wet mix controls how far that tail moves forward.
The SuperCollider room value is 0.402295 and damping is 0.71875. These dimensionless settings are choices for this algorithm, rather than equivalent values for Ableton decay or Csound feedback and damping. More damping darkens the circulating highs. Any input filters and mid/side width changes in this stage retain their own explicit settings in the full script.
| SuperCollider room control | Value |
|---|---|
| FreeVerb2 internal mix | 1, wet output only |
| Room | 0.402295 |
| Damping | 0.71875 |
| Predelay | 12 ms |
| External room wet | 14% |
| SuperCollider control | Value |
|---|---|
| Room side multiplier | 1 |
| Room input cuts | Off |
Sound after step 4 — WebM/Opus
Next: Set the final width and gain →Step 05 / 5
Set the final width and gain #
Set ~soundStage = 5 in the full script. Use -2.99 dB gain after the effects. Scale the side signal by 1, preserving the center. Apply LeakDC DC removal with coefficient 0.995. The fixed ~soundOutputScale gain follows the complete effect chain at every stage. The effects Synth reads the stereo bus after the note group, and continues through note releases.
| SuperCollider control | Value |
|---|---|
| Final gain | -2.99 dB |
| Width | 1 × side |
| Bass side cutoff | Off |
| DC removal | LeakDC, coefficient 0.995 |
Sound after step 5 — WebM/Opus
Audio & settings ↓