Step 01 / 5
Build the detuned source and amplitude contour #
Set giStage init 1 in the full script. Use 3 band-limited saw voices at -13 dB each, spread by 7.2 cents between adjacent voices. Reverse the stereo weights across the channels. The amplitude opens in 0.66 seconds, decays over 2.01 seconds to 0.794328, and releases over 1.87 seconds. Basic Shapes is represented by this explicit waveform; Shimmer, where present, becomes slow independent pitch drift rather than the original unison engine.
| Csound control | Value |
|---|---|
| Sources | 3 × saw, -13 dB |
| Adjacent pitch spacing | 7.2 cents |
| Amp A/D/S/R | 0.66 s / 2.01 s / 0.794328 / 1.87 s |
| Instrument gain | -8 dB |
| Velocity multiplier | 0.4 + 0.6 × velocity |
Sound after step 1 — WebM/Opus
Next: Blend the second source and animate the filters →Step 02 / 5
Blend the second source and animate the filters #
Set giStage init 2 in the full script. Add a pulse layer at -16 dB, 0 semitones and 5 cents. The bandpass center starts from 839 Hz and moves by 0.8 octaves under the second envelope. A positive depth opens the spectral ceiling; a negative depth moves the notch downward. The serial second filter keeps the specified high or low edge under control. Exact wavetable morphing, Warp/Fold and free-running source modulation are not implemented; the code below defines the chosen static spectra and note-local drift.
| Csound control | Value |
|---|---|
| Secondary layer | pulse, -16 dB; 0 st; 5 cents |
| Filter 1 | Bandpass, 839 Hz base, 0.8 octave depth |
| Filter contour | 1.8 / 3 / 0.6 / 2.4 |
| Filter 2 | Lowpass at 6.20 kHz |
| Pulse width | 0.56 |
Sound after step 2 — WebM/Opus
Next: Add moving stereo chorus →Step 03 / 5
Add moving stereo chorus #
Set giStage init 3 in the full script. Move two delay taps around 20 ms by ±3.6 ms at 0.3 Hz, with opposite phases and 22% wet mix. Highpass only the wet inputs at 220 Hz to leave the direct low body clear. Scale side information by 1.05; tap feedback is 0. These explicit tap depths interpret the source Amount and ensemble movement rather than copy the internal algorithm. Sustained notes reveal slow pitch interference.
| Csound control | Value |
|---|---|
| Tap center / excursion | 20 / ±3.6 ms |
| Rate / wet | 0.3 Hz / 22% |
| Wet highpass | 220 Hz |
| Width / feedback | 1.05 / 0 |
| Warmth shaping | 0% smooth-drive interpretation |
Sound after step 3 — WebM/Opus
Next: Surround the tone with a damped room →Step 04 / 5
Surround the tone with a damped room #
Set giStage init 4 in the full script. Feed the preceding signal through 28 ms predelay into reverbsc, with feedback 0.8219, 3300 Hz damping and 25% wet mix. Predelay leaves the initial articulation in front; feedback prolongs the tail, while damping darkens repeated circulation. The source room decay setting is 3.57 seconds, but Csound feedback is not a decay-time control: this is an interpretation of that space, with different diffusion and modulation.
| Csound control | Value |
|---|---|
| Source decay target | 3.57 s (not a measured Csound decay) |
| Predelay / feedback | 28 ms / 0.8219 |
| Damping / wet | 3300 Hz / 25% |
| Room side multiplier | 1 |
| Room input cuts | Off |
Sound after step 4 — WebM/Opus
Next: Set the final width and gain →Step 05 / 5
Set the final width and gain #
Set giStage init 5 in the full script. Use 9.08 dB gain after the effects. Scale the side signal by 1, preserving the center. Highpass only the side at 180 Hz to focus the lowest frequencies. Apply order-2048 DC removal, using a longer window to limit low-note loss. The fixed output-scale control at the end of instrument 90 remains a separate Csound gain setting. Clear the shared note buses only after processing them; effect memories continue carrying their own tails.
| Csound control | Value |
|---|---|
| Final gain | 9.08 dB |
| Width | 1 × side |
| Bass side cutoff | 180 Hz |
| DC removal | Order 2048 |
Sound after step 5 — WebM/Opus
Audio & settings ↓