Step 01 / 5
Build the detuned source and amplitude contour #
Select ~soundStage = 1 and evaluate the full script at the end of this guide. Wait for the instrument-ready message before playing.
Set ~soundStage = 1 in the full script. Use 3 band-limited saw voices at -13 dB each, spread by 7.2 cents between adjacent voices. Reverse the stereo weights across the channels. The amplitude opens in 0.66 seconds, decays over 2.01 seconds to 0.794328, and releases over 1.87 seconds. Basic Shapes is represented by this explicit waveform; Shimmer, where present, becomes slow independent pitch drift rather than the original unison engine.
| SuperCollider control | Value |
|---|---|
| Sources | 3 × saw, -13 dB |
| Adjacent pitch spacing | 7.2 cents |
| Amp A/D/S/R | 0.66 s / 2.01 s / 0.794328 / 1.87 s |
| Instrument gain | -8 dB |
| Velocity multiplier | 0.4 + 0.6 × velocity |
Sound after step 1 — WebM/Opus
Next: Blend the second source and animate the filters →Step 02 / 5
Blend the second source and animate the filters #
Set ~soundStage = 2 in the full script. Add a pulse layer at -16 dB, 0 semitones and 5 cents. The bandpass center starts from 839 Hz and moves by 0.8 octaves under the second envelope. A positive depth opens the spectral ceiling; a negative depth moves the notch downward. The serial second filter keeps the specified high or low edge under control. Exact wavetable morphing, Warp/Fold and free-running source modulation are not implemented; the code below defines the chosen static spectra and note-local drift.
| SuperCollider control | Value |
|---|---|
| Secondary layer | pulse, -16 dB; 0 st; 5 cents |
| Filter 1 | Bandpass, 839 Hz base, 0.8 octave depth |
| Filter contour | 1.8 / 3 / 0.6 / 2.4 |
| Filter 2 | Lowpass at 6.20 kHz |
| Pulse width | 0.56 |
Sound after step 2 — WebM/Opus
Next: Add moving stereo chorus →Step 03 / 5
Add moving stereo chorus #
Set ~soundStage = 3 in the full script. Move two delay taps around 20 ms by ±3.6 ms at 0.3 Hz, with opposite phases and 22% wet mix. Highpass only the wet inputs at 220 Hz to leave the direct low body clear. Scale side information by 1.05; tap feedback is 0. These explicit tap depths interpret the source Amount and ensemble movement rather than copy the internal algorithm. Sustained notes reveal slow pitch interference.
| SuperCollider control | Value |
|---|---|
| Tap center / excursion | 20 / ±3.6 ms |
| Rate / wet | 0.3 Hz / 22% |
| Wet highpass | 220 Hz |
| Width / feedback | 1.05 / 0 |
| Warmth shaping | 0% smooth-drive interpretation |
Sound after step 3 — WebM/Opus
Next: Surround the tone with a damped room →Step 04 / 5
Surround the tone with a damped room #
Set ~soundStage = 4 and evaluate the full block. Feed the preceding signal into FreeVerb2, using its fully wet output and the dry/wet routing shown in the script. The room continues after individual note envelopes release. Predelay separates the initial articulation from the diffuse tail; the external wet mix controls how far that tail moves forward.
The SuperCollider room value is 0.773607 and damping is 0.79375. These dimensionless settings are choices for this algorithm, rather than equivalent values for Ableton decay or Csound feedback and damping. More damping darkens the circulating highs. Any input filters and mid/side width changes in this stage retain their own explicit settings in the full script.
| SuperCollider room control | Value |
|---|---|
| FreeVerb2 internal mix | 1, wet output only |
| Room | 0.773607 |
| Damping | 0.79375 |
| Predelay | 28 ms |
| External room wet | 25% |
| SuperCollider control | Value |
|---|---|
| Room side multiplier | 1 |
| Room input cuts | Off |
Sound after step 4 — WebM/Opus
Next: Set the final width and gain →Step 05 / 5
Set the final width and gain #
Set ~soundStage = 5 in the full script. Use 9.08 dB gain after the effects. Scale the side signal by 1, preserving the center. Highpass only the side at 180 Hz to focus the lowest frequencies. Apply LeakDC DC removal with coefficient 0.995. The fixed ~soundOutputScale gain follows the complete effect chain at every stage. The effects Synth reads the stereo bus after the note group, and continues through note releases.
| SuperCollider control | Value |
|---|---|
| Final gain | 9.08 dB |
| Width | 1 × side |
| Bass side cutoff | 180 Hz |
| DC removal | LeakDC, coefficient 0.995 |
Sound after step 5 — WebM/Opus
Audio & settings ↓