Slate Cove — complete SuperCollider settings
Signal flow and implementation #
~soundStage is compiled into the SynthDefs. Re-evaluate the complete block after changing it; source and effects are then replaced together. The fixed output multiplier ~soundOutputScale is 2.331539 and applies after the whole chain at every stage. It is separate from any final gain step.
EnvGen supplies the explicit linear or exponential contours. Exponential floors stay positive. Closing the gate begins each release; a separate silent lifetime envelope frees the note after the longest source release. Shared effects continue independently.
BPF and BRF use bandwidth divided by center frequency as reciprocal Q. The narrow noise resonances, where present, use SuperCollider normalization and need their own instrument gain.
LeakDC uses coefficient 0.995. It replaces the longer-window Csound DC blocker, with a different low-frequency response and latency.
LocalIn/LocalOut carry all feedback paths in a single multichannel loop. Recirculation adds one server processing block to each delay; changing block size therefore changes short comb/flanger tuning. DelayC uses seconds, converted from the millisecond tap values in the design.
FreeVerb2 replaces the diffuse room with its own room and damping controls, both dimensionless. The per-stage values below are specific to this algorithm and do not specify a measured decay time or damping frequency.
Saw and Pulse use SuperCollider oscillator implementations and startup phases; they replace the source engines and do not scan proprietary wavetables.
Synthesis and effect controls #
Stage 1 — Build the detuned source and amplitude contour #
Select ~soundStage = 1 and evaluate the full script at the end of this guide. Wait for the instrument-ready message before playing.
Set ~soundStage = 1 in the full script. Use 3 band-limited saw voices at -13 dB each, spread by 7.2 cents between adjacent voices. Reverse the stereo weights across the channels. The amplitude opens in 0.66 seconds, decays over 2.01 seconds to 0.794328, and releases over 1.87 seconds. Basic Shapes is represented by this explicit waveform; Shimmer, where present, becomes slow independent pitch drift rather than the original unison engine.
| SuperCollider control | Value |
|---|---|
| Sources | 3 × saw, -13 dB |
| Adjacent pitch spacing | 7.2 cents |
| Amp A/D/S/R | 0.66 s / 2.01 s / 0.794328 / 1.87 s |
| Instrument gain | -8 dB |
| Velocity multiplier | 0.4 + 0.6 × velocity |
Stage 2 — Blend the second source and animate the filters #
Set ~soundStage = 2 in the full script. Add a pulse layer at -16 dB, 0 semitones and 5 cents. The bandpass center starts from 839 Hz and moves by 0.8 octaves under the second envelope. A positive depth opens the spectral ceiling; a negative depth moves the notch downward. The serial second filter keeps the specified high or low edge under control. Exact wavetable morphing, Warp/Fold and free-running source modulation are not implemented; the code below defines the chosen static spectra and note-local drift.
| SuperCollider control | Value |
|---|---|
| Secondary layer | pulse, -16 dB; 0 st; 5 cents |
| Filter 1 | Bandpass, 839 Hz base, 0.8 octave depth |
| Filter contour | 1.8 / 3 / 0.6 / 2.4 |
| Filter 2 | Lowpass at 6.20 kHz |
| Pulse width | 0.56 |
Stage 3 — Add moving stereo chorus #
Set ~soundStage = 3 in the full script. Move two delay taps around 20 ms by ±3.6 ms at 0.3 Hz, with opposite phases and 22% wet mix. Highpass only the wet inputs at 220 Hz to leave the direct low body clear. Scale side information by 1.05; tap feedback is 0. These explicit tap depths interpret the source Amount and ensemble movement rather than copy the internal algorithm. Sustained notes reveal slow pitch interference.
| SuperCollider control | Value |
|---|---|
| Tap center / excursion | 20 / ±3.6 ms |
| Rate / wet | 0.3 Hz / 22% |
| Wet highpass | 220 Hz |
| Width / feedback | 1.05 / 0 |
| Warmth shaping | 0% smooth-drive interpretation |
Stage 4 — Surround the tone with a damped room #
Set ~soundStage = 4 and evaluate the full block. Feed the preceding signal into FreeVerb2, using its fully wet output and the dry/wet routing shown in the script. The room continues after individual note envelopes release. Predelay separates the initial articulation from the diffuse tail; the external wet mix controls how far that tail moves forward.
The SuperCollider room value is 0.773607 and damping is 0.79375. These dimensionless settings are choices for this algorithm, rather than equivalent values for Ableton decay or Csound feedback and damping. More damping darkens the circulating highs. Any input filters and mid/side width changes in this stage retain their own explicit settings in the full script.
| SuperCollider room control | Value |
|---|---|
| FreeVerb2 internal mix | 1, wet output only |
| Room | 0.773607 |
| Damping | 0.79375 |
| Predelay | 28 ms |
| External room wet | 25% |
| SuperCollider control | Value |
|---|---|
| Room side multiplier | 1 |
| Room input cuts | Off |
Stage 5 — Set the final width and gain #
Set ~soundStage = 5 in the full script. Use 9.08 dB gain after the effects. Scale the side signal by 1, preserving the center. Highpass only the side at 180 Hz to focus the lowest frequencies. Apply LeakDC DC removal with coefficient 0.995. The fixed ~soundOutputScale gain follows the complete effect chain at every stage. The effects Synth reads the stereo bus after the note group, and continues through note releases.
| SuperCollider control | Value |
|---|---|
| Final gain | 9.08 dB |
| Width | 1 × side |
| Bass side cutoff | 180 Hz |
| DC removal | LeakDC, coefficient 0.995 |
Connected instrument #
The full SuperCollider script contains the complete voice, shared effects, bus ordering and note helper. No external sample or third-party unit is required.