Step 01 / 5
Excite a decaying string mode bank #
Select ~soundStage = 1 and evaluate the full script at the end of this guide. Wait for the instrument-ready message before playing.
Set ~soundStage = 1 in the full script. Feed a 1.5 ms shaped pulse with a quiet noise component into sixteen string modes. The strike position is 0.28 of string length and the pickup position 0.22. Each mode is weighted by the sine of both positions, so moving the strike changes which harmonics are suppressed. A small stiffness term bends upper partials away from perfect harmonic ratios. The fundamental T60 is 3.4 s and upper modes decay faster. This modal bank interprets Tension rather than implementing its plectrum and string solver.
| SuperCollider control | Value |
|---|---|
| Strike / pickup | 0.28 / 0.22 of length |
| Mode frequencies | f × n × sqrt(1 + 0.00008 × n²), below 11000 Hz |
| Decay | T60 / (1 + 0.08 × (n−1)^1.3) |
| Fundamental T60 | 3.4 s |
| Exciter lowpass | 4300 Hz |
| String scaling / instrument | 0.02 × (0.4 + 0.6 × velocity) / −10 dB |
Sound after step 1 — WebM/Opus
Next: Blend body modes and soften the string →Step 02 / 5
Blend body modes and soften the string #
Set ~soundStage = 2 in the full script. Use broad body resonances at 97, 193 and 450 Hz with Q values 8, 12 and 18. Blend 12% of their weighted sum with the string and lowpass at 7300 Hz. The body colors the lower spectrum rather than supplying a sustained oscillator. Natural mode tails continue after the short excitation; the script holds their state for twice the fundamental T60. Body size, damping and pickup geometry are represented by these explicit choices, not a numerical conversion of all Tension macros.
| SuperCollider control | Value |
|---|---|
| Body modes | 97/193/450 Hz; Q 8/12/18 |
| Body weights / scale | 0.4/0.2/0.1 × 0.04 |
| Body mix | 12% |
| Lowpass | 7300 Hz |
The Q values describe the design targets: Ringz receives decay seconds computed as Q × ln(1000) / (π × frequency), not Q itself.
Sound after step 2 — WebM/Opus
Next: Round the signal with saturation →Step 03 / 5
Round the signal with saturation #
Set ~soundStage = 3 in the full script. Use +1 dB drive with 30% shaped signal and -1 dB output trim. The smooth curve is tanh(input × 3 × drive.dbamp) / 3; the other portion stays clean. Louder peaks enter its curved region more strongly, adding harmonics and rounding the envelope. This interprets the source saturation curve rather than implementing its proprietary transfer function.
| SuperCollider control | Value |
|---|---|
| Drive / output | 1 / -1 dB |
| Shaped mix | 30% |
| Input DC removal | LeakDC, coefficient 0.995 |
Sound after step 3 — WebM/Opus
Next: Surround the tone with a damped room →Step 04 / 5
Surround the tone with a damped room #
Set ~soundStage = 4 and evaluate the full block. Feed the preceding signal into FreeVerb2, using its fully wet output and the dry/wet routing shown in the script. The room continues after individual note envelopes release. Predelay separates the initial articulation from the diffuse tail; the external wet mix controls how far that tail moves forward.
The SuperCollider room value is 0.29377 and damping is 0.71875. These dimensionless settings are choices for this algorithm, rather than equivalent values for Ableton decay or Csound feedback and damping. More damping darkens the circulating highs. Any input filters and mid/side width changes in this stage retain their own explicit settings in the full script.
| SuperCollider room control | Value |
|---|---|
| FreeVerb2 internal mix | 1, wet output only |
| Room | 0.29377 |
| Damping | 0.71875 |
| Predelay | 12 ms |
| External room wet | 12% |
| SuperCollider control | Value |
|---|---|
| Room side multiplier | 1 |
| Room input cuts | Off |
Sound after step 4 — WebM/Opus
Next: Set the final width and gain →Step 05 / 5
Set the final width and gain #
Set ~soundStage = 5 in the full script. Use 23.1 dB gain after the effects. Scale the side signal by 1, preserving the center. Apply LeakDC DC removal with coefficient 0.995. The fixed ~soundOutputScale gain follows the complete effect chain at every stage. The effects Synth reads the stereo bus after the note group, and continues through note releases.
| SuperCollider control | Value |
|---|---|
| Final gain | 23.1 dB |
| Width | 1 × side |
| Bass side cutoff | Off |
| DC removal | LeakDC, coefficient 0.995 |
Sound after step 5 — WebM/Opus
Audio & settings ↓