Step 01 / 5
Shape the sine body #
Set giStage init 1 in the full script. Use a retriggered sine at -8.0 dB, transposed 0 semitones. Attack is 0.0003 seconds, exponential decay 0.11 seconds, sustain 0 and release 0.08 seconds. Positive exponential floors stand in for silence. The contour starts again for each score note; it differs from Operator's Trigger envelope behavior on very short held notes.
| Csound control | Value |
|---|---|
| Carrier | Sine, phase 0 |
| Amplitude A/D/S/R | 0.0003 / 0.11 / 0 / 0.08 |
| Instrument gain | -12 dB |
| Transpose | 0 st |
Sound after step 1 — WebM/Opus
Next: Build the characteristic spectrum →Step 02 / 5
Build the characteristic spectrum #
Set giStage init 2 in the full script. Add a separately decaying white-noise layer at −5 dB with 190 ms decay and 100 ms release. Highpass the combined body at 160 Hz, leaving a pitched knock underneath the noise snap. The exact source circuit and low-level envelope behavior are represented by the explicit code in the full script.
| Csound control | Value |
|---|---|
| Added source / motion | White noise: −5 dB; 190 ms decay |
| Filter | 160 Hz |
| Filter type | Highpass |
Sound after step 2 — WebM/Opus
Next: Round the signal with saturation →Step 03 / 5
Round the signal with saturation #
Set giStage init 3 in the full script. Use +3 dB drive with 60% shaped signal and -2 dB output trim. The smooth curve is tanh(input × 3 × ampdb(drive)) / 3; the other portion stays clean. Louder peaks enter its curved region more strongly, adding harmonics and rounding the envelope. This interprets the source saturation curve rather than implementing its proprietary transfer function.
| Csound control | Value |
|---|---|
| Drive / output | 3 / -2 dB |
| Shaped mix | 60% |
| Input DC removal | Order 2048 |
Sound after step 3 — WebM/Opus
Next: Surround the tone with a damped room →Step 04 / 5
Surround the tone with a damped room #
Set giStage init 4 in the full script. Feed the preceding signal through 5 ms predelay into reverbsc, with feedback 0.35, 4500 Hz damping and 9% wet mix. Predelay leaves the initial articulation in front; feedback prolongs the tail, while damping darkens repeated circulation. The source room decay setting is 0.45 seconds, but Csound feedback is not a decay-time control: this is an interpretation of that space, with different diffusion and modulation.
| Csound control | Value |
|---|---|
| Source decay target | 0.45 s (not a measured Csound decay) |
| Predelay / feedback | 5 ms / 0.35 |
| Damping / wet | 4500 Hz / 9% |
| Room side multiplier | 1 |
| Room input cuts | Off |
Sound after step 4 — WebM/Opus
Next: Set the final width and gain →Step 05 / 5
Set the final width and gain #
Set giStage init 5 in the full script. Use -0.77 dB gain after the effects. Average the channels for identical mono outputs. Apply order-2048 DC removal, using a longer window to limit low-note loss. The fixed output-scale control at the end of instrument 90 remains a separate Csound gain setting. Clear the shared note buses only after processing them; effect memories continue carrying their own tails.
| Csound control | Value |
|---|---|
| Final gain | -0.77 dB |
| Width | Mono |
| Bass side cutoff | Off |
| DC removal | Order 2048 |
Sound after step 5 — WebM/Opus
Audio & settings ↓