Step 01 / 5
Shape the sine body #
Set giStage init 1 in the full script. Use a retriggered sine at -8.0 dB, transposed 0 semitones. Attack is 0.012 seconds, exponential decay 0.8 seconds, sustain 1 and release 0.17 seconds. Positive exponential floors stand in for silence. The contour starts again for each score note; it differs from Operator's Trigger envelope behavior on very short held notes.
| Csound control | Value |
|---|---|
| Carrier | Sine, phase 0 |
| Amplitude A/D/S/R | 0.012 / 0.8 / 1 / 0.17 |
| Instrument gain | -8.0 dB |
| Transpose | 0 st |
Sound after step 1 — WebM/Opus
Next: Build the characteristic spectrum →Step 02 / 5
Build the characteristic spectrum #
Set giStage init 2 in the full script. Add parallel sines at ratios 2, 3 and 4 with levels −13, −19 and −24 dB. They use the same amplitude contour. A tracked 5600 Hz lowpass softens the upper edge without turning the additive layers into FM. The exact source circuit and low-level envelope behavior are represented by the explicit code in the full script.
| Csound control | Value |
|---|---|
| Added source / motion | Sine ratios 2/3/4: −13/−19/−24 dB |
| Filter | 5.60 kHz |
| Filter type | Lowpass |
Sound after step 2 — WebM/Opus
Next: Add moving stereo chorus →Step 03 / 5
Add moving stereo chorus #
Set giStage init 3 in the full script. Move two delay taps around 12 ms by ±3.6 ms at 0.65 Hz, with opposite phases and 22% wet mix. Highpass only the wet inputs at 180 Hz to leave the direct low body clear. Scale side information by 1; tap feedback is 0. These explicit tap depths interpret the source Amount and ensemble movement rather than copy the internal algorithm. Sustained notes reveal slow pitch interference.
| Csound control | Value |
|---|---|
| Tap center / excursion | 12 / ±3.6 ms |
| Rate / wet | 0.65 Hz / 22% |
| Wet highpass | 180 Hz |
| Width / feedback | 1 / 0 |
| Warmth shaping | 0% smooth-drive interpretation |
Sound after step 3 — WebM/Opus
Next: Surround the tone with a damped room →Step 04 / 5
Surround the tone with a damped room #
Set giStage init 4 in the full script. Feed the preceding signal through 12 ms predelay into reverbsc, with feedback 0.6918, 4500 Hz damping and 18% wet mix. Predelay leaves the initial articulation in front; feedback prolongs the tail, while damping darkens repeated circulation. The source room decay setting is 1.9 seconds, but Csound feedback is not a decay-time control: this is an interpretation of that space, with different diffusion and modulation.
| Csound control | Value |
|---|---|
| Source decay target | 1.9 s (not a measured Csound decay) |
| Predelay / feedback | 12 ms / 0.6918 |
| Damping / wet | 4500 Hz / 18% |
| Room side multiplier | 1 |
| Room input cuts | Off |
Sound after step 4 — WebM/Opus
Next: Set the final width and gain →Step 05 / 5
Set the final width and gain #
Set giStage init 5 in the full script. Use -7.37 dB gain after the effects. Scale the side signal by 1, preserving the center. Highpass only the side at 140 Hz to focus the lowest frequencies. Apply order-2048 DC removal, using a longer window to limit low-note loss. The fixed output-scale control at the end of instrument 90 remains a separate Csound gain setting. Clear the shared note buses only after processing them; effect memories continue carrying their own tails.
| Csound control | Value |
|---|---|
| Final gain | -7.37 dB |
| Width | 1 × side |
| Bass side cutoff | 140 Hz |
| DC removal | Order 2048 |
Sound after step 5 — WebM/Opus
Audio & settings ↓