Step 01 / 5
Excite a decaying string mode bank #
Set giStage init 1 in the full script. Feed a 1.5 ms shaped pulse with a quiet noise component into sixteen string modes. The strike position is 0.13 of string length and the pickup position 0.22. Each mode is weighted by the sine of both positions, so moving the strike changes which harmonics are suppressed. A small stiffness term bends upper partials away from perfect harmonic ratios. The fundamental T60 is 2.6 s and upper modes decay faster. This modal bank interprets Tension rather than implementing its plectrum and string solver.
| Csound control | Value |
|---|---|
| Strike / pickup | 0.13 / 0.22 of length |
| Mode frequencies | f × n × sqrt(1 + 0.00008 × n²), below 11000 Hz |
| Decay | T60 / (1 + 0.08 × (n−1)^1.3) |
| Fundamental T60 | 2.6 s |
| Exciter lowpass | 4780 Hz |
| String scaling / instrument | 0.02 × (0.4 + 0.6 × velocity) / −10 dB |
Sound after step 1 — WebM/Opus
Next: Blend body modes and soften the string →Step 02 / 5
Blend body modes and soften the string #
Set giStage init 2 in the full script. Use broad body resonances at 97, 193 and 450 Hz with Q values 8, 12 and 18. Blend 28% of their weighted sum with the string and lowpass at 3900 Hz. The body colors the lower spectrum rather than supplying a sustained oscillator. Natural mode tails continue after the short excitation; the script holds their state for twice the fundamental T60. Body size, damping and pickup geometry are represented by these explicit choices, not a numerical conversion of all Tension macros.
| Csound control | Value |
|---|---|
| Body modes | 97/193/450 Hz; Q 8/12/18 |
| Body weights / scale | 0.4/0.2/0.1 × 0.04 |
| Body mix | 28% |
| Lowpass | 3900 Hz |
Sound after step 2 — WebM/Opus
Next: Round the signal with saturation →Step 03 / 5
Round the signal with saturation #
Set giStage init 3 in the full script. Use +0.5 dB drive with 30% shaped signal and -1 dB output trim. The smooth curve is tanh(input × 3 × ampdb(drive)) / 3; the other portion stays clean. Louder peaks enter its curved region more strongly, adding harmonics and rounding the envelope. This interprets the source saturation curve rather than implementing its proprietary transfer function.
| Csound control | Value |
|---|---|
| Drive / output | 0.5 / -1 dB |
| Shaped mix | 30% |
| Input DC removal | Order 2048 |
Sound after step 3 — WebM/Opus
Next: Surround the tone with a damped room →Step 04 / 5
Surround the tone with a damped room #
Set giStage init 4 in the full script. Feed the preceding signal through 12 ms predelay into reverbsc, with feedback 0.5101, 4500 Hz damping and 12% wet mix. Predelay leaves the initial articulation in front; feedback prolongs the tail, while damping darkens repeated circulation. The source room decay setting is 1.04 seconds, but Csound feedback is not a decay-time control: this is an interpretation of that space, with different diffusion and modulation.
| Csound control | Value |
|---|---|
| Source decay target | 1.04 s (not a measured Csound decay) |
| Predelay / feedback | 12 ms / 0.5101 |
| Damping / wet | 4500 Hz / 12% |
| Room side multiplier | 1 |
| Room input cuts | Off |
Sound after step 4 — WebM/Opus
Next: Set the final width and gain →Step 05 / 5
Set the final width and gain #
Set giStage init 5 in the full script. Use 17.4 dB gain after the effects. Scale the side signal by 1, preserving the center. Apply order-2048 DC removal, using a longer window to limit low-note loss. The fixed output-scale control at the end of instrument 90 remains a separate Csound gain setting. Clear the shared note buses only after processing them; effect memories continue carrying their own tails.
| Csound control | Value |
|---|---|
| Final gain | 17.4 dB |
| Width | 1 × side |
| Bass side cutoff | Off |
| DC removal | Order 2048 |
Sound after step 5 — WebM/Opus
Audio & settings ↓