Step 01 / 5
Build the first oscillator and touch contour #
Set giStage init 1 in the full script. Use saw at -8 dB with pulse width 50% when applicable. The contour has 0.035 s attack, 0.85 s exponential decay to 0.8 sustain and 0.35 s release. Multiply by velocity^3; this explicit power curve interprets the source velocity response. Keep the signal centered before adding effects.
| Csound control | Value |
|---|---|
| Source | Saw, -8.0 dB; width not used |
| Amplitude A/D/S/R | 0.035 / 0.85 / 0.8 / 0.35 |
| Amplifier / instrument | -6.0 dB / -6.0 dB |
| Velocity power | 3.0 |
Sound after step 1 — WebM/Opus
Next: Add the second oscillator and resonant contour →Step 02 / 5
Add the second oscillator and resonant contour #
Set giStage init 2 in the full script. Add rect at -15 dB, tuned by 0 octaves. Use a Low-pass 12dB/oct interpretation with 950 Hz base cutoff, 2 octave envelope depth and 0.6 octave-per-octave pitch tracking. The contour opens then settles quickly while the amplitude remains. Smooth input drive interprets Sym1; the ladder or second-order lowpass is a different circuit. The 0 Hz LFO, where enabled, restarts per score note rather than running freely.
| Csound control | Value |
|---|---|
| Second source | Rect; -15 dB; width 46 % |
| Filter base / resonance | 950 Hz / 0.2 |
| Filter A/D/S/R | 0.07 / 0.35 / 0.45 / 0.42 |
| Envelope / key / LFO depth | 2 / 0.6 / 0 octaves |
| LFO rate | 0 Hz |
| Filter input shape | tanh(input × 1.4) / 1.4 |
Sound after step 2 — WebM/Opus
Next: Add moving stereo chorus →Step 03 / 5
Add moving stereo chorus #
Set giStage init 3 in the full script. Move two delay taps around 12 ms by ±2.8 ms at 0.4 Hz, with opposite phases and 16% wet mix. Highpass only the wet inputs at 200 Hz to leave the direct low body clear. Scale side information by 1; tap feedback is 0. These explicit tap depths interpret the source Amount and ensemble movement rather than copy the internal algorithm. Sustained notes reveal slow pitch interference.
| Csound control | Value |
|---|---|
| Tap center / excursion | 12 / ±2.8 ms |
| Rate / wet | 0.4 Hz / 16% |
| Wet highpass | 200 Hz |
| Width / feedback | 1 / 0 |
| Warmth shaping | 0% smooth-drive interpretation |
Sound after step 3 — WebM/Opus
Next: Surround the tone with a damped room →Step 04 / 5
Surround the tone with a damped room #
Set giStage init 4 in the full script. Feed the preceding signal through 12 ms predelay into reverbsc, with feedback 0.6065, 4500 Hz damping and 14% wet mix. Predelay leaves the initial articulation in front; feedback prolongs the tail, while damping darkens repeated circulation. The source room decay setting is 1.4 seconds, but Csound feedback is not a decay-time control: this is an interpretation of that space, with different diffusion and modulation.
| Csound control | Value |
|---|---|
| Source decay target | 1.4 s (not a measured Csound decay) |
| Predelay / feedback | 12 ms / 0.6065 |
| Damping / wet | 4500 Hz / 14% |
| Room side multiplier | 1 |
| Room input cuts | Off |
Sound after step 4 — WebM/Opus
Next: Set the final width and gain →Step 05 / 5
Set the final width and gain #
Set giStage init 5 in the full script. Use 7.95 dB gain after the effects. Scale the side signal by 1, preserving the center. Apply order-2048 DC removal, using a longer window to limit low-note loss. The fixed output-scale control at the end of instrument 90 remains a separate Csound gain setting. Clear the shared note buses only after processing them; effect memories continue carrying their own tails.
| Csound control | Value |
|---|---|
| Final gain | 7.95 dB |
| Width | 1 × side |
| Bass side cutoff | Off |
| DC removal | Order 2048 |
Sound after step 5 — WebM/Opus
Audio & settings ↓