Sorrel Hollow — complete SuperCollider settings
Signal flow and implementation #
~soundStage is compiled into the SynthDefs. Re-evaluate the complete block after changing it; source and effects are then replaced together. The fixed output multiplier ~soundOutputScale is 1.267126 and applies after the whole chain at every stage. It is separate from any final gain step.
EnvGen supplies the explicit linear or exponential contours. Exponential floors stay positive. Closing the gate begins each release; a separate silent lifetime envelope frees the note after the longest source release. Shared effects continue independently.
MoogFF replaces the ladder filter. Its gain argument is four times the source 0–1 resonance amount, limited to 3.95; it is a different circuit. Cutoffs are limited to 20–18000 Hz.
LeakDC uses coefficient 0.995. It replaces the longer-window Csound DC blocker, with a different low-frequency response and latency.
Saw and Pulse use SuperCollider oscillator implementations and startup phases; they replace the source engines and do not scan proprietary wavetables.
Synthesis and effect controls #
Stage 1 — Shape the drifting bass body #
Select ~soundStage = 1 and evaluate the full script at the end of this guide. Wait for the instrument-ready message before playing.
Set ~soundStage = 1 in the full script. Use saw at -8.0 dB, with ±0.6 cents of slow note-local pitch drift. Set attack 0.0068 s, decay 1.29 s, sustain 0.7 and release 0.203 s. Keep the source centered. This replaces Drift's irregular oscillator instability with a small sine drift; glide and mono note-priority are not implemented.
| SuperCollider control | Value |
|---|---|
| Wave / gain | Saw / -8.0 dB |
| Amplitude A/D/S/R | 0.0068 / 1.29 / 0.7 / 0.203 |
| Instrument / velocity | -6.0 dB / 40 % |
| Drift | ±0.6 cents at 0.19 Hz |
Stage 2 — Add the sub and lowpass movement #
Set ~soundStage = 2 in the full script. Add an octave-down sine at -7.0 dB. Route both sources through a 244 Hz ladder lowpass with 0.25 resonance, followed by the 25 Hz highpass. The second envelope moves cutoff by 0.9 octaves; keyboard and velocity amounts add their own opening. The filter type and modulation scaling interpret the source rather than copy its Type II circuit.
| SuperCollider control | Value |
|---|---|
| Sub | Octave down, -7.0 dB |
| Cutoff / resonance | 244 Hz / 0.25 |
| Filter A/D/S/R | 0.002 / 0.45 / 0.2 / 0.2 |
| Envelope / key / velocity depth | 0.9 / 0.6 / 0.24 octaves |
For MoogFF, multiply the stated source resonance amount by four to obtain its 0–4 gain argument (limited to 3.95). The complete script gives this gain expression beside each cutoff.
Stage 3 — Round the signal with saturation #
Set ~soundStage = 3 in the full script. Use +2.3 dB drive with 70% shaped signal and -2 dB output trim. The smooth curve is tanh(input × 3 × drive.dbamp) / 3; the other portion stays clean. Louder peaks enter its curved region more strongly, adding harmonics and rounding the envelope. This interprets the source saturation curve rather than implementing its proprietary transfer function.
| SuperCollider control | Value |
|---|---|
| Drive / output | 2.3 / -2 dB |
| Shaped mix | 70% |
| Input DC removal | LeakDC, coefficient 0.995 |
Stage 4 — Set the final width and gain #
Set ~soundStage = 4 in the full script. Use 2.86 dB gain after the effects. Average the channels for identical mono outputs. Apply LeakDC DC removal with coefficient 0.995. The fixed ~soundOutputScale gain follows the complete effect chain at every stage. The effects Synth reads the stereo bus after the note group, and continues through note releases.
| SuperCollider control | Value |
|---|---|
| Final gain | 2.86 dB |
| Width | Mono |
| Bass side cutoff | Off |
| DC removal | LeakDC, coefficient 0.995 |
Connected instrument #
The full SuperCollider script contains the complete voice, shared effects, bus ordering and note helper. No external sample or third-party unit is required.