Step 01 / 4
Build the low body and reedy upper edge #
Set giStage init 1 in the full script. Use a 10% pulse at −8 dB and a quiet upper sine at +16 st/−14 cents, −21 dB. A mild tanh shape interprets the upper source warp. Bandpass the main pair at 400 Hz and notch near 805 Hz, while allowing the octave-down sine to bypass those filters and preserve the low anchor. That explicit sub bypass is a Csound interpretation of the source balance. Use a 24 ms opening, full sustain and 3.3 s release.
| Csound control | Value |
|---|---|
| Main / upper | Pulse width 0.10 at −8 dB; sine +16 st/−14 cents at −21 dB |
| Sub | Octave-down sine, 0 dB, bypasses main filters |
| Filters | 400 Hz bandpass, bandwidth = center; 805 Hz notch, bandwidth = 15% center |
| Tracking | Bandpass 70%; notch 100% |
| Amplitude | 24 ms / 1.28 s / full / 3.3 s |
| Touch | 0.2 + 0.8 × velocity |
Sound after step 1 — WebM/Opus
Next: Let the bandpass rise after the attack →Step 02 / 4
Let the bandpass rise after the attack #
Set giStage init 2 in the full script. Open the bandpass by 0.4 octaves under a 510 ms / 1.81 s / zero / 1.35 s contour. The amplitude arrives much earlier than the filter peak, making the color swell over the established low body. The modulation depth and bandwidth interpret the source matrix and resonance values rather than copy its circuits.
| Csound control | Value |
|---|---|
| Filter contour | 510 ms / 1.81 s / zero / 1.35 s |
| Filter motion | +0.4 octaves |
Sound after step 2 — WebM/Opus
Next: Round the signal with saturation →Step 03 / 4
Round the signal with saturation #
Set giStage init 3 in the full script. Use +3 dB drive with 100% shaped signal and -3 dB output trim. The smooth curve is tanh(input × 3 × ampdb(drive)) / 3; the other portion stays clean. Louder peaks enter its curved region more strongly, adding harmonics and rounding the envelope. This interprets the source saturation curve rather than implementing its proprietary transfer function.
| Csound control | Value |
|---|---|
| Drive / output | 3 / -3 dB |
| Shaped mix | 100% |
| Input DC removal | Off |
Sound after step 3 — WebM/Opus
Next: Widen a dark room around the horn →Step 04 / 4
Widen a dark room around the horn #
Set giStage init 4 in the full script. Feed the preceding signal through 10 ms predelay into reverbsc, with feedback 0.9252, 2500 Hz damping and 40% wet mix. Predelay leaves the initial articulation in front; feedback prolongs the tail, while damping darkens repeated circulation. The source room decay setting is 9 seconds, but Csound feedback is not a decay-time control: this is an interpretation of that space, with different diffusion and modulation. The room input is highpassed at 275 Hz and lowpassed at 4400 Hz, leaving the direct body separate. Use 1.5 dB gain after the effects. Scale the side signal by 3, preserving the center. Leave final DC removal off. The fixed output-scale control at the end of instrument 90 remains a separate Csound gain setting. Clear the shared note buses only after processing them; effect memories continue carrying their own tails.
| Csound control | Value |
|---|---|
| Source decay target | 9 s (not a measured Csound decay) |
| Predelay / feedback | 10 ms / 0.9252 |
| Damping / wet | 2500 Hz / 40% |
| Room side multiplier | 1 |
| Room input cuts | 275 / 4400 Hz |
| Final gain | 1.5 dB |
| Width | 3 × side |
| Bass side cutoff | Off |
| DC removal | Off |
Sound after step 4 — WebM/Opus
Audio & settings ↓