playgrid.ccRead tutorial

Tutorial 161 / Ableton Live

How to Make a Deep Sub Bass with Ableton Drift — Willow Arc

Learn how to make a deep sub bass in Ableton Live with Drift's triangle and octave-down sine, low-pass contour, Soft Sine saturation and mono Utility.

4 stepsDriftLive 12 Suite

Listen to the finished sound

Download WEBM ↓

Follow the synthesis steps in order. Use the audio examples and device settings alongside the instructions.

Step 01 / 4

Build the triangle bass body and amplitude contour

Set oscillator 1 to Triangle at -10 dB. Its sparse upper harmonics give the bass a clearer pitch outline than a sine alone, while leaving space for the deeper oscillator added next. With oscillator 1’s filter routing off, this stage exposes the raw source before the low-pass contour.

Envelope 1 opens in 9.87 ms, decays for 687 ms to an 85% sustain level, and releases in 144 ms. The fast-but-not-instant attack softens the leading edge, the small decay drop lets the body settle, and the short release keeps low notes from leaving a long tail. Velocity-to-volume at 45% makes harder playing louder without changing the oscillator balance.

Use Drift with the complete starting settings. Set the source and amplitude controls below; sections marked Off stay bypassed at this stage.

Signal flow: Drift → Saturator → Utility. Begin with the instrument, then add each effect in its numbered step.

Control Value
Osc 1 Wave Triangle
Osc 1 Gain -10 dB
Osc 1 Oct 0
Env 1 Attack 9.87 ms
Env 1 Decay 687 ms
Env 1 Sustain 85 %
Env 1 Release 144 ms
Osc 1 Shape Mod Amt 0.0 %
Vel > Vol 45 %
Drift 2.0 %
Spread 0.0 %
Glide Time 45.0 ms
Volume -8.0 dB
Osc 2 On Off
Noise On Off
Osc 1 Flt On Off

Voicing and modulation

Set the voice options and modulation source/destination menus below. Their amounts appear in the Drift parameter table. A source has no effect when its amount is zero or its destination is None.

Control Value
Filter modulation source 1 Env 2
Filter modulation source 2 Vel
LFO modulation source Mod
Pitch modulation source 1 Env 2
Pitch modulation source 2 LFO
Shape modulation source Slide
Modulation row 1 source Mod
Modulation row 2 source Vel
Modulation row 3 source Press
Modulation row 1 destination LP Frequency
Modulation row 2 destination None
Modulation row 3 destination None
Voice count 8
Voice mode Mono

Use the voicing and modulation settings for the oscillator choices, voice mode and modulation routes.

Willow Arc — Drift — step 1
Willow Arc — Drift — step 1 · Select image to enlarge

Sound after step 1 — WebM/Opus

Next: Add octave-down sine weight and the low-pass contour →

Step 02 / 4

Add octave-down sine weight and the low-pass contour

Enable oscillator 2 as a sine at -6 dB and tune it one octave down. Because it is louder and lower than the triangle, it becomes the deep foundation while the triangle remains as upper definition. Keep Spread at 0% and Drift at 2% so the low end stays centered and the pitch remains stable.

Route the oscillators through the Type II low-pass filter at 151 Hz. Envelope 2 adds a modest 12% opening contour, then decays over 380 ms to 15% sustain, so the attack begins slightly brighter and settles into the darker body. The 8% velocity route adds a little more brightness to stronger playing. The 24 Hz high-pass cutoff removes only the lowest edge of the spectrum, while 70% key tracking helps higher notes retain definition.

Keep the first stage’s source and amplitude settings while making these changes. The complete instrument settings show the resulting tone before effects.

Control Value
Osc 2 Wave Sine
Osc 2 Gain -6.0 dB
Osc 2 Oct -1
Noise On Off
LP Type II
LP Freq 151 Hz
LP Res 0.12
HP Freq 24.0 Hz
Key > LPF 0.70
LP Mod Amt 1 12 %
LP Mod Amt 2 8.0 %
Env 2 Attack 4.00 ms
Env 2 Decay 380 ms
Env 2 Sustain 15 %
Env 2 Release 160 ms
Mod Matrix Amt 1 0.0 %
Osc 2 On On
Osc 1 Flt On On
Willow Arc — Drift — step 2
Willow Arc — Drift — step 2 · Select image to enlarge

Sound after step 2 — WebM/Opus

Next: Add restrained saturation harmonics →

Step 03 / 4

Add restrained saturation harmonics

Choose the Soft Sine curve and raise Drive to 2.8 dB. At 55% Dry/Wet, Saturator adds controlled upper harmonics around the sine-heavy core, helping the bass read on smaller playback systems without turning it into a bright distorted bass. The -2 dB output offsets part of the added level, Pre DC Filter removes DC before the waveshaping stage, and Color remains off so the curve is not tilted toward another frequency range.

Control Value
Type Soft Sine
Drive 2.8 dB
Output -2.0 dB
Color On Off
Pre Dc Filter On
Dry/Wet 55 %

Place Saturator after Drift. The complete settings include its remaining controls.

Willow Arc — Saturator — step 3
Willow Arc — Saturator — step 3 · Select image to enlarge

Sound after step 3 — WebM/Opus

Next: Center the finished sub in mono →

Step 04 / 4

Center the finished sub in mono

Turn Mono on in Utility so the entire bass is summed to the center. This is more decisive than Bass Mono and suits a patch whose triangle, sine and saturation are all intended as one stable low-frequency source. Set Utility’s Gain knob to the Output value in the table; this restores final level but does not create the bass weight. Keep DC Filter on and the phase-inversion switches off.

Control Value
Output 7.43 dB
DC Filter On
Mono On

Place Utility after Saturator. The complete settings include its remaining controls.

Willow Arc — Utility — step 4
Willow Arc — Utility — step 4 · Select image to enlarge

Sound after step 4 — WebM/Opus

Audio & settings ↓

Audio & settings

Audio recordings and settings for this tutorial.